Comparison

BAKFlip MX4 vs Lomax Stance: Which Is Better? (November 2026)

Updated on · By the SidekickSays team

The BAKFlip MX4 wins the BAKFlip MX4 vs Lomax Stance comparison for most truck owners. It folds to the cab for near-full bed access, locks with a tailgate latch, and the Gen 3 build adds strength and weather sealing. The Lomax Stance suits owners who want a lower, flatter hard cover.

On this page (8 sections)
  1. BAKFlip MX4 vs Lomax Stance: the quick verdict
  2. The two covers side by side
  3. Bed access: where the MX4 pulls ahead
  4. Security: auto-latch vs a low-profile lock
  5. Weather sealing and the Gen 3 build
  6. Fit and installation: two MX4 beds, one Stance
  7. Which cover suits your truck and your loads?
  8. BAKFlip MX4 vs Lomax Stance: which should you buy?

The BAKFlip MX4 wins the BAKFlip MX4 vs Lomax Stance comparison for most truck owners. It folds toward the cab for 100% bed access, locks with the tailgate, and the Gen 3 build adds a stronger aluminum frame and tighter weather seals.

The Lomax Stance is the choice when you want a low, flat hard cover and less bulk in the folded stack.

Both covers are hard folding tonneaus, so both give you a locked lid over your cargo. The decision comes down to how much bed access you want when the cover is open and how much cab-side space you can give up.

This comparison looks at the design, access, security, fit and weather differences between the BAKFlip MX4 and the Lomax Stance. The MX4 is the cover we'd pick overall, and the two MX4 fitments here cover the F-150 and Super Duty beds.

RealTruck BAKFlip MX4 Hard Folding TruckBest for full bed access

RealTruck BAKFlip MX4 Hard Folding Truck

9.4/10Our score

See it on Amazon

RealTruck BAKFlip MX4 Hard Folding TruckBest for Super Duty beds

RealTruck BAKFlip MX4 Hard Folding Truck

9.1/10Our score

See it on Amazon

BAKFlip MX4 vs Lomax Stance: the quick verdict

Pick the BAKFlip MX4 for the best mix of bed access, locking security and weather sealing. Pick the Lomax Stance if a low-profile look and a flatter folded stack matter more than a cover that folds fully to the cab.

The MX4 earns our 9.4 score on the F-150 fitment. It's a four-panel hard folding cover with a matte black aluminum finish and a tailgate lock.

BAK says the Gen 3 version is 22 percent stronger than the previous generation and uses revised EPDM perimeter seals.

The Lomax Stance is also a hard folding cover, and its main draw is a lower, flatter profile. It has its own locking setup and seals, but its panels don't open the bed as completely as the MX4's fold-to-cab design.

For most readers shopping the BAKFlip MX4 vs Lomax Stance question, the MX4 is the better buy. It gives you more usable bed space when open and a more established security system.

The two covers side by side

The table below lines up the features that decide this comparison. Read it as a shortlist, then use the sections after it to see which difference matters for your truck.

ProductBest forFitStyleLockOur score
RealTruck BAKFlip MX4 Hard Folding Truckfull bed access2021–2026 Ford F-150, 5 ft 7 in bedHard folding, 4 panelsTailgate9.4
RealTruck BAKFlip MX4 Hard Folding TruckSuper Duty beds2017–2026 Ford F-250/350 Super Duty, 6 ft 10 in bedHard folding, 4 panelsTailgate9.1

What the comparison table shows

The biggest split is panel travel. The MX4 folds its panels all the way to the cab and secures them there, so you can drive with the cover fully open.

That's the feature that sets it apart from most folding covers.

The Stance's lower profile changes how the cover sits on the bed rails. A flatter lid looks cleaner and catches less wind, but the panels still stack when open.

That stack eats into the front of the bed.

Both covers are aluminum and both lock through the tailgate latch. The difference is in how much bed you can reclaim when the cover is open.

Where the two covers are closest

Locking is the least important difference. The MX4's auto-latch engages when the cover closes and locks with the tailgate.

A tailgate-latch lock is a theft deterrent, not a vault, on either cover.

Fit is a bigger difference, but only because the two MX4 boxes fit different trucks. The Stance has its own fitment list.

Check your cab and bed length against the cover you're buying before anything else.

Bed access: where the MX4 pulls ahead

The MX4 gives 100% bed access when open, while the Stance trades some of that for a flatter folded stack. If you load tall items or use the whole bed, the MX4's design is the reason to choose it.

BAK says the MX4 panels "fold to the cab, easily secure, and safely drive with the cover fully open." That means you can carry a fridge, a ladder or a load of lumber with the cover still mounted and locked open.

A folding cover that stops short of the cab leaves a stack of panels behind the cab. That stack sits over the front of the bed.

For tall cargo, it's the difference between fitting and not fitting.

If you regularly haul full-height loads, this is the deciding feature. For a truck used mostly for groceries and tools, the difference matters less.

When a flat folded stack is enough

The Stance's lower profile appeals to owners who want the cover to look like part of the truck. A flatter lid also leaves a tidier line when closed.

If your loads are short and you rarely need the full bed height, a flatter stack won't get in your way. The look and the wind profile become the main reasons to pick it.

The MX4's matte black finish is also subtle. It's a flush-mount design with a textured matte-black finish across all surfaces.

So the appearance edge for the Stance is small, not decisive.

Security: auto-latch vs a low-profile lock

Both covers lock through the tailgate latch, so security is close. The MX4's upgraded auto-latch is the more refined system, but neither cover turns your bed into a safe.

The MX4's Gen 3 design "secures the cover automatically when closed," according to BAK. New lock components add resistance to tampering and forced entry.

That's a real upgrade over the older latch.

The Stance locks too, and it sits lower on the rails. A low lid is slightly harder to pry at the edge, which helps a little.

But a tailgate-latch lock only works while the tailgate is shut.

If you park in high-theft areas, don't rely on the cover's latch alone. Lock the tailgate and keep valuables out of sight.

The cover is a deterrent, not a replacement for common sense.

What each lock means day to day

The MX4's auto-latch closes itself as you lower the last panel. You don't have to reach for a separate latch or key each time.

That's a small convenience that adds up over a week of errands.

The Stance's latch works in the same tailgate-linked way. It just uses a flatter mechanism under the low lid.

Neither lock needs a separate key for the cover, since the tailgate lock does the work.

If you want the cover to lock without touching a key, the MX4's auto-latch is the nicer system. If you already lock your tailgate out of habit, either one is fine.

Weather sealing and the Gen 3 build

The MX4's Gen 3 version has the newest seals and clamps in this comparison. That makes it the safer pick for a truck that sits outside in rain and snow.

BAK says the Gen 3 MX4 has revised EPDM perimeter seals and tight-fit clamps. It also adds a longer dual-action tailgate seal that keeps the tailgate weatherproofed whether the cover is open or closed.

BAK tested the cover from -40 to 180°F and zero to 95% humidity.

The Stance uses its own perimeter seals. It's a hard cover, so it keeps most rain out along the rails.

The difference is in how the seals are engineered and how well the corners close.

For most owners, the MX4's sealing is the more complete package. The tailgate seal is the part that matters most, since that's where water usually gets in.

Strength and the 22 percent claim

BAK says the Gen 3 MX4 is 22 percent stronger than the previous generation. The frame uses alloy-based construction with heavy-duty aluminum side rails and top panels reinforced with high-density polymer cores.

The Stance is built as a low, flat cover, so its strength comes from its panel design rather than a tall folding frame. It holds up to normal loads, but the MX4's reinforced build is the more heavy-duty option.

If you carry heavy gear on top of the cover or drive rough roads, the MX4's stronger frame is the better fit. For light daily use, either cover handles the load.

Fit and installation: two MX4 beds, one Stance

The MX4 comes in fitments for the F-150 5 ft 7 in bed and the Super Duty 6 ft 10 in bed; the Stance has its own fitment list. Check your truck's bed length and cab style before you order either cover.

The F-150 MX4 (B08L44X6NZ) fits 2021–2026 F-150 trucks, including the Raptor and Lightning, with the 5 ft 7 in (67.1 in) bed. That's the most common F-150 bed length.

The Super Duty MX4 (B071JR545L) fits 2017–2026 F-250 and F-350 trucks with the 6 ft 10 in (81.9 in) bed. The box weighs about 70 lb, so plan on two people to lift it.

The Stance is sold in its own truck-specific fitments. Match the cover's fitment to your exact model year and bed length.

A cover for a different bed won't seal or lock correctly.

Installation time and tools

BAK says the MX4's new click-in rail system cuts install time by up to 12 percent compared with the older design. You still mount rails, set the panels and adjust the clamps.

The install needs basic hand tools and a helper for the panels. Plan an afternoon for the first fit, and check the clamp tension before the first rain.

The Stance installs in a similar way, with its own rail and clamp hardware. Its flatter panels are lighter to handle, which can make the lift easier for one person.

Which fitment to buy

Buy the MX4 for the F-150 if you drive a 2021–2026 F-150 with the 5 ft 7 in bed. Buy the Super Duty MX4 if you drive a 2017–2026 F-250 or F-350 with the 6 ft 10 in bed.

Buy the Stance if your truck isn't covered by these two MX4 fitments or if you want the low-profile look. Just confirm the Stance's fitment for your exact bed first.

Which cover suits your truck and your loads?

Choose the MX4 for full bed access and the stronger Gen 3 build; choose the Stance for the low, flat look. Your truck's bed length and your usual cargo decide more than the brand name.

Who should buy the BAKFlip MX4?

Pick the MX4 if you haul tall items and want the bed fully open while driving. The fold-to-cab design is the practical feature you'll use every time you move furniture or lumber.

Pick it if you want the latest BAK build. The Gen 3 version adds strength and tighter seals, and the 5-year extended warranty covers it.

The F-150 version is our top pick overall.

It's also the better choice if you park outside. The revised seals and longer tailgate seal are the newest weather protection in this comparison.

Who should buy the Lomax Stance?

Pick the Stance if you want a low, flat hard cover and you rarely need the full bed height. Its flatter lid sits closer to the rails and looks cleaner on the truck.

Pick it if your truck's bed isn't covered by the two MX4 fitments here. The Stance's fitment list may include your model, and a cover that fits your bed beats one that doesn't.

It's also a reasonable pick if you want a folding cover but don't need to drive fully open. The stack is shorter and less in the way for light loads.

What about storage and add-ons?

If you run a cross-bed toolbox, both covers need checking. A folding cover's stack can clash with a mounted box.

Our guide to a tonneau cover with toolbox explains which types leave room for storage.

If you're also weighing a full enclosure, our tonneau cover vs camper shell comparison helps you decide between a lid and a shell. A camper shell gives more height and weather protection but changes the truck's profile.

And if you're still unsure about hard versus soft, our soft vs hard tonneau cover guide covers the trade-offs. Hard covers cost more and weigh more, but they lock and hold up better.

BAKFlip MX4 vs Lomax Stance: which should you buy?

Buy the BAKFlip MX4 for most trucks and most loads. It folds fully to the cab, locks with the tailgate, and the Gen 3 build is the strongest and best-sealed version BAK has made.

The F-150 fitment is our top pick.

The Lomax Stance is the right cover when a low, flat lid matters more than full bed access. It's a solid hard cover, but it doesn't reclaim the whole bed the way the MX4 does.

If your truck is an F-150 or Super Duty with the matching bed, the MX4 decision is easy. Check the fitment first, then buy the MX4.

If your truck isn't covered, look at the Stance's fitment list before you rule it out.

For a closer look at how the MX4 stacks up against another premium hard cover, our BAKFlip MX4 vs Diamondback comparison covers that matchup. It helps if you're deciding between a folding cover and a heavier-duty lid.

Frequently asked questions

Does the BAKFlip MX4 work with a truck bed toolbox?

A folding MX4 can clash with a cross-bed toolbox, because the panels stack toward the cab when open. Measure the toolbox depth against the folded stack, and look at covers designed to work around storage if you keep a box mounted all the time.

Can you drive with the BAKFlip MX4 fully open?

BAK says yes. The panels fold to the cab and secure there, so the cover stays open while you drive.

Check that the straps are latched before you pull away, and keep the tailgate closed for the lock to hold.

Does the Lomax Stance cover the whole truck bed?

The Stance is a hard folding cover, so it covers the bed opening and folds back in sections when you need space. The folded panels still sit above the cab-side bed area, so plan around that if you load tall items near the front.

Is the BAKFlip MX4 hard to install?

BAK says the Gen 3 click-in rail system cuts install time by up to 12 percent compared with the older design. It still takes two people to lift the panels onto the rails, so set aside an afternoon and have a helper.

Which cover keeps rain out better, the MX4 or the Stance?

Both use perimeter seals and clamps to keep water out along the rails. The MX4's revised EPDM seals and tight-fit clamps are the newest version of BAK's weather sealing, so it is the safer pick if your truck sits outside in heavy rain.

Do both covers lock?

The MX4 locks through the tailgate latch, so closing the tailgate locks the cover. The Lomax Stance also offers tailgate-latch locking.

Either way, a locked tailgate is only as secure as the truck's own lock.