Comparison

Extang Solid Fold vs BAKFlip: Which Fits You? (November 2026)

Updated on · By the SidekickSays team

Pick the BAKFlip MX4 for most trucks, because its panel and frame specs are clearer and it folds to open the full bed. Choose the Extang Solid Fold when its own listed fit matches your bed and you want a simpler panel design.

On this page (8 sections)
  1. Extang Solid Fold vs BAKFlip MX4 at a glance
  2. Which cover fits your truck?
  3. How do the cab and frame compare?
  4. Which keeps your gear safer?
  5. Which seals tighter against rain?
  6. How much bed access do you get?
  7. Which suits how you load the truck?
  8. Which cover is the better buy?

Pick the BAKFlip MX4 for most trucks, because it has the clearer panel and frame specs and it folds to open the whole bed. The extang solid fold cover vs bakflip choice comes down to fit, security and how you use the bed.

Both are hard folding covers built from aluminum panels, so both guard the bed better than a soft cover. The decision is about what each one offers beyond that basic job.

Here is how the two compare on the points that actually change what you buy.

RealTruck BAK BAKFlip MX4 Hard Folding TruckBest for Ford F-150 owners

RealTruck BAK BAKFlip MX4 Hard Folding Truck

9.4/10Our score

See it on Amazon

RealTruck BAK BAKFlip MX4 Hard Folding TruckBest for Ram 1500 owners

RealTruck BAK BAKFlip MX4 Hard Folding Truck

9.2/10Our score

See it on Amazon

Extang Solid Fold vs BAKFlip MX4 at a glance

The MX4 gives you more detail on how it is built; the Solid Fold is a simpler panel cover. The specifications for the MX4 line up neatly across the two fits covered here.

The F-150 fit is aluminum with a matte aluminum finish. The Ram fit is aluminum, and the trim there is simply listed as aluminum.

Both MX4 models fold fully to the cab and open the entire bed. That is the feature that separates a folding cover from a roll-up in daily use.

What the Solid Fold has going for it is a straightforward panel design. Read the fit line closely, since the version that matches your truck is the only one that works.

The table below sets the two MX4 fits beside each other so the differences are easy to scan. The parts list is the same shape in both cases: the cover, the side rails and the hardware, plus an install guide on the F-150 version.

The Ram fit ships as the cover, two side rails and a hardware pack. If you are the kind of buyer who wants to know what arrives in the box before you order, that level of detail is a point in the MX4 column.

If you are still weighing a basic soft cover, our soft vs hard tonneau cover guide explains where folding panels win and where they lose.

Which cover fits your truck?

The cover you can mount is the only one worth comparing, and the BAKFlip MX4 has clear fit lines for two popular trucks. The F-150 version is for 2021-2026 trucks with the 5' 7" bed.

That F-150 fit includes the Raptor and the Lightning. Both are the same short bed, so the rail geometry and clamp layout follow the standard truck.

The Ram version is for 2019-2026 Ram 1500 trucks with the 5' 7" bed. It does not fit trucks with the multi-function split tailgate.

That split tailgate matters because the MX4 locks through the tailgate. If your Ram has the two-part tailgate, this cover is not the version for your truck.

For the Extang Solid Fold, the truck has to match its own fit listing. Check the full fit note for either brand, not just the brand name.

Why the bed length is the first number to check

A 5' 7" bed is not the same footprint on every truck. The Ford version is listed at 67.1 inches, and the Ram version is listed at 67.4 inches.

Those fractions of an inch are the reason the two part numbers exist. The rails, the clamps and the seal lines are cut to the truck, so one cover does not slide onto the other truck's bed.

The F-150 line also covers the Raptor and the Lightning. That matters if you drive a performance or electric F-150, since those trucks often get skipped in fit notes written only for the standard model.

On the Ram side, the exclusion for the multi-function split tailgate is the one fit detail people miss. Check your tailgate before you order, not after.

How do the cab and frame compare?

The MX4 has a stronger construction story than the Solid Fold, thanks to its alloy frame and polymer-cored panels. That frame is what holds the panels flat across the bed.

The MX4 uses heavy-duty aluminum side rails and top panels reinforced with high-density polymer cores. The maker says this design adds 22 percent in strength over the previous generation.

That number is a maker claim. Even without it, aluminum rails mean the cover resists bending under a load far better than a soft top.

The panels are finished in matte aluminum on the F-150 fit. The low-profile flush mount sits close to the bed rails, so it does not stand up like a tall cap.

What the Gen 3 changes mean for daily use

The panels are not just aluminum skins. Each one carries a high-density polymer core inside the alloy frame, which is how the cover holds its shape when something heavy rests on it.

The flush-mount design also matters for how the truck sits. A cover that stands proud of the rails changes the profile and can interfere with how cargo slides across the top.

The F-150 fit lists a matte aluminum exterior finish, while the Ram fit lists the finish simply as aluminum. If the look of the cover matters to you, the matte treatment is the one to confirm for your truck.

The Solid Fold is a sound option for a basic hard cover, but the data here does not spell out its panel structure the way BAK does. If frame detail matters to you, the MX4 makes the case better.

Which keeps your gear safer?

The BAKFlip MX4 locks through the tailgate with an auto-latch, which is stronger security than a cover that rests on a latch alone. The MX4 is built to keep the bed closed when the truck is locked.

The Gen 3 MX4 uses a patented auto-latching system that locks the cover as it closes. New lock parts add resistance to tampering and forced entry.

The tailgate lock type means the cover follows the truck's own tailgate. If your tailgate can be dropped from inside the bed, the cover is only as locked as the tailgate is.

How the tailgate lock actually works

When the cover is closed, the latch system engages on its own. You do not have to reach up and snap a strap or turn a separate key on the cover itself.

From there, the truck's tailgate lock is the gate. Lock the truck and the cover stays shut with it, so there is one key and one habit instead of two.

That is why the Ram split tailgate fit is excluded. The cover ties its security to a standard tailgate design.

The Solid Fold uses its own latching approach, so check how it locks before you assume it matches the MX4. For most buyers, a cover tied to the tailgate lock is the easier one to live with, since it adds no extra key.

Which seals tighter against rain?

The MX4 was revised for better weather sealing, with EPDM perimeter seals and tight-fit clamps along the bed rails. That is where water tends to get in first.

Revised seals run around the perimeter, and tight-fit clamps hold the cover close to the rails. A longer dual-action tailgate seal keeps the tailgate edge covered whether the cover is open or shut.

The maker says it was tested from -40 to 180°F with humidity from zero to 95 percent. Treat that as a maker claim about extremes, not a promise your bed stays dry in a car wash.

The three leak points the design targets

Water gets into a truck bed in three common spots. The first is the rail line where the cover meets the bedside, and that is what the perimeter seals and tight-fit clamps address.

The second is the tailgate gap. The dual-action tailgate seal is built to close that edge while still letting the tailgate swing open and shut as normal.

The third is the corner where the rails, the cab and the tailgate all meet. EPDM is the seal material to look for, because it holds up to sun and cold better than a plain rubber strip.

No folding cover keeps a pressurized spray out entirely. Still, a cover with a full perimeter seal and tight clamps does more than a soft cover with elastic corners.

The Solid Fold's sealing details are not spelled out in the same way here. If the bed carries tools and materials you want shielded from rain, the seal detail favors the MX4.

How much bed access do you get?

Both MX4 fits fold to the cab so the full bed opens, and you can drive with the cover folded. That is the single biggest reason to pick a folding design.

When you fold the panels up, they stack against the cab and lock there. The bed is then open top to tail, with no wasted floor space while parked or moving.

For a truck that hauls lumber, mulch or a bike one day and keeps cargo covered the next, that range matters. You do not have to remove the cover to use the bed.

Folding part way versus folding all the way

Many hard covers let you fold one or two panels back and leave the rest in place. That is handy when you need to reach in over the side, but it leaves a panel over the front of the bed.

The MX4 goes all the way. The panels stack against the cab and secure there, so the full floor is open from the tailgate to the cab wall.

That also means you can drive with the cover open. You fold it up at the lumber yard, strap it down, and hit the road without taking the cover off the truck.

A cover that only folds partway keeps the last panel over the bed, which eats the height you just freed. If you also carry a toolbox, the fold-forward design leaves more space than a fixed or roll-up cover.

Our tonneau cover with toolbox guide covers which types fit around a chest box.

Which suits how you load the truck?

Pick the BAKFlip MX4 if you want the clearest build and security detail; pick the Extang Solid Fold if its fit line is the one that matches your truck. Loading habits decide the rest.

Who should buy the F-150 MX4

The F-150 5' 7" fit suits 2021-2026 owners, including Raptor and Lightning drivers. The matte aluminum finish and low profile keep the truck looking clean.

Its auto-latch and tailgate lock suit anyone who leaves tools or gear in the bed between jobs. The full fold-to-cab opening suits weekend hauling.

Who should buy the Ram MX4

The Ram 1500 5' 7" fit suits 2019-2026 owners without the split tailgate. The tailgate lock type and full bed access carry over unchanged.

This version rounds out the line where the F-150 fit leaves off. Our Tonno Pro tri-fold vs BAKFlip comparison shows how a simpler tri-fold stacks up against these folding panels.

Who should buy the Extang Solid Fold

Choose the Solid Fold when its listed fit matches your bed and you like a plain panel cover. It is a solid choice for a buyer who wants a hard top and does not need the extra frame detail.

If you are deciding between a cover and a full enclosure, our tonneau cover vs camper shell rundown helps you see the trade-off in height and access.

Which cover is the better buy?

For most trucks, the BAKFlip MX4 is the better buy. It gives you full bed access, a tailgate lock and a sealed rail edge.

The warranty gap to weigh

The two MX4 fits do not carry the same warranty in this data. The F-150 fit lists an extended 5-year warranty, while the Ram fit lists 3 years.

That is worth checking against your own truck before you order. A longer warranty on the Ford side gives that fit a slight edge if you plan to keep the truck a long time.

The Ram fit carries the same folding design and weather detail, with a 3-year warranty listed instead. The multi-function tailgate exclusion is the main thing to check on a Ram.

The Extang Solid Fold is not a bad cover. It is simply less detailed here, so its strengths are harder to compare against the MX4's frame and sealing story.

Pick the MX4 if you want a hard folding cover with the full spec picture and the fold-to-cab opening. Pick the Solid Fold only when its fit matches and a simpler cover suits your use.

That is the short version of the extang solid fold cover vs bakflip call: the MX4 wins on detail, security and bed access for most buyers.

Our score weighs specs, features and buyer feedback against what you're shopping for.

Frequently asked questions

Does the BAKFlip MX4 fit a Ram 1500 with the split tailgate?

No. The 448227 fit is listed for 2019-2026 Ram 1500 trucks with the 5' 7" bed but not those with the multi-function split tailgate.

The cover uses a tailgate lock, so that tailgate design has to match the cover.

How much of the bed can I use with a hard folding cover?

A folding design like the MX4 folds to the cab so the whole bed opens, and you can drive with it that way. That matters if you carry tall loads now and then.

A cover that only folds part way leaves the last section in place.

Do hard folding covers keep water out?

A quality hard folding cover uses perimeter seals and clamps along the bed rails to limit water. The MX4 uses revised EPDM seals and tight-fit clamps.

Heavy rain and pressure washing can still put some water past any cover, so treat it as protection from weather rather than a dry box.